Чтобы управлять найстройками профиля, вашими избранными лотами, ставками и выставлять товары на торги.
Наличие : в наличии
Техническое состояние : исправное
Состояние : новое
Гарантия : гарантия от продавца
Плата (модуль) управления нагрузкой С РЕВЕРСОМ (двигатель, вентилятор...) 433MHz DC12V 3А беспроводный с пультом ДУ Wireless Remote Control
Рабочая частота: 433MHz.
Кодировка: 1527 Learning Code.
Диапазон рабочего напряжения: DC 3.6...18 V.
Потребляемый ток (режим ожидания): <5mA>Допустимая нагрузка:
DC 3A.
Receive sensitivity:<-108dB.
Дальность действия пульта: 50 м (в пределах прямой видимости).
Частота (Transmission Rate): 10KHz.
Frequency Deviation: ±0.2MHz.
Модуляция:ASK (superheterodyne)
Размеры платы: 30*13*5 мм
Допустимое количество привязки пультов: 4
Рабочие режимы (Working mode): Momentary, Toggle, Latching
Mode+stop, clear code
Обучение (привязка пультов): кнопка на плате (Learning Button)
Диапазон рабочих температур: -20...80 С.
Комплектация:
- плата (модуль) управления нагрузкой - 1 шт;
- пульт ДУ 433 МГц - 1 шт;
#6580
Програмирование пультов:
Operation method:
Clear the code: (Before switching the mode, you must
first clear the code)
Press the learn code button 8 times, and the LED goes out. LED
flashes 5 times, clear OK. (If you need to change the working mode
of the same remote control, please clear the code before
learning)
Learn to code:
1. Jog: Press the learning button once, the module LED light will
turn on once, enter the learning state, the led light will turn on,
use the remote control to press the button to match the code, the
led light will flash three times (it will not light up in the
learning state), continue to press The second button is to pair the
code, the led light flashes three times, and the code is
successfully clicked. (The first button is forward jog, the second
button is reverse jog)
2. Self-locking: Press the learning button twice, the module led
light will turn on twice, and the led light will turn on after
entering the learning state. Press the key on the remote control to
match the code, the led light flashes three times and turns on (it
will not light up in the learning state) Continue to press the
second button to pair the code, the led light flashes three times,
and the self-locking code is successful (the first button is
forward rotation and self-locking (press the second button to
stop), and the second button is reverse rotation and
self-locking)
3. Interlock + stop function: press the learning button three
times, the module led light will be on three times and off, the led
light will be on after entering the learning state, press the key
on the remote control to pair the code, the first time the key is
pressed to learn the forward rotation, press the second key
Learning is reverse, the third key is to stop, the LED light
flashes three times after learning, the interlocking code is
successful (the first key is forward, the second is reverse, and
the third is stop).
4. Clear code: Press 8 times to clear the code.
Предоплата
Оплата при получении
По договоренности/другое
Стандартный банковский перевод
Оплата курьеру
Онлайн-перевод
Новая почта по городу: 46 грн. по стране: 46 грн.
Укрпочта по городу: 30 грн. по стране: 30 грн.
Курьерская служба по городу: 46 грн. по стране: 46 грн.