HDD Seagate Baracuda 80Gb PATA

Данные SMART отчетов:

smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-45-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus
Device Model: ST380011A
Serial Number: 5JVLHSVT
Firmware Version: 8.01
User Capacity: 80 026 361 856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-6 T13/1410D revision 2
Local Time is: Sun Oct 30 14:39:06 2016 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 055 052 006 Pre-fail Always - 144767775
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 19
5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 47
7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 204696658
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 10648
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1775
194 Temperature_Celsius 0x0022 048 055 000 Old_age Always - 48
195 Hardware_ECC_Recovered 0x001a 055 051 000 Old_age Always - 144767775
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 035 000 Old_age Always - 3873
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 1993 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1993 occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 95 e5 b5 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00b5e595 = 11920789

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 98 fe e4 b5 e0 00 00:00:39.612 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:38.907 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:00:38.261 RECALIBRATE [OBS-4]
25 00 98 fe e4 b5 e0 00 00:00:38.181 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:38.008 READ DMA EXT

Error 1992 occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 95 e5 b5 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00b5e595 = 11920789

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 98 fe e4 b5 e0 00 00:00:39.612 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:00:38.907 RECALIBRATE [OBS-4]
25 00 98 fe e4 b5 e0 00 00:00:38.261 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:38.181 READ DMA EXT
00 00 43 00 00 00 00 06 00:00:38.008 NOP [Abort queued commands]

Error 1991 occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 95 e5 b5 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00b5e595 = 11920789

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 98 fe e4 b5 e0 00 00:00:35.311 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:38.907 READ DMA EXT
00 00 43 00 00 00 00 06 00:00:38.261 NOP [Abort queued commands]
ef 03 43 95 e5 b5 e0 02 00:00:38.181 SET FEATURES [Set transfer mode]
25 00 98 fe e4 b5 e0 00 00:00:38.008 READ DMA EXT

Error 1990 occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 95 e5 b5 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00b5e595 = 11920789

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 98 fe e4 b5 e0 00 00:00:35.311 READ DMA EXT
00 00 43 00 00 00 00 06 00:00:35.300 NOP [Abort queued commands]
ef 03 43 95 e5 b5 e0 02 00:00:38.261 SET FEATURES [Set transfer mode]
25 00 98 fe e4 b5 e0 00 00:00:38.181 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:38.008 READ DMA EXT

Error 1989 occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 95 e5 b5 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00b5e595 = 11920789

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 98 fe e4 b5 e0 00 00:00:35.311 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:35.300 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:00:35.292 RECALIBRATE [OBS-4]
25 00 98 fe e4 b5 e0 00 00:00:35.291 READ DMA EXT
25 00 98 fe e4 b5 e0 00 00:00:35.290 READ DMA EXT

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00648 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-45-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus
Device Model: ST380011A
Serial Number: 5JVLHSVT
Firmware Version: 8.01
User Capacity: 80 026 361 856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-6 T13/1410D revision 2
Local Time is: Sun Oct 30 14:39:11 2016 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 055 052 006 - 144767785
3 Spin_Up_Time PO---- 099 098 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 19
5 Reallocated_Sector_Ct PO--CK 099 099 036 - 47
7 Seek_Error_Rate POSR-- 083 060 030 - 204696676
9 Power_On_Hours -O--CK 088 088 000 - 10648
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 099 020 - 1775
194 Temperature_Celsius -O---K 048 055 000 - 48
195 Hardware_ECC_Recovered -O-RC- 055 051 000 - 144767785
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 035 000 - 3873
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xff GPL - 24064 Reserved

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 1993 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1993 [12] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 1e 00 b1 2e e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 9b 00 c3 2e e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 76 e0 00 00:01:02.278 READ DMA EXT

Error 1992 [11] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.774 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.102 READ DMA EXT
10 00 00 00 3f 00 00 00 00 00 00 e0 00 00:01:02.443 RECALIBRATE [OBS-4]
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.278 READ DMA EXT

Error 1991 [10] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.774 READ DMA EXT
10 00 00 00 3f 00 00 00 00 00 00 e0 00 00:01:03.102 RECALIBRATE [OBS-4]
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:02.278 READ DMA EXT

Error 1990 [9] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.102 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 1e 00 b1 2e e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 9b 00 c3 2e e0 00 00:01:02.278 READ DMA EXT

Error 1989 [8] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 1e 00 b1 2e e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 9b 00 c3 2e e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 76 e0 00 00:01:02.278 READ DMA EXT

Error 1988 [7] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.774 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.102 READ DMA EXT
10 00 00 00 3f 00 00 00 00 00 00 e0 00 00:01:02.443 RECALIBRATE [OBS-4]
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.278 READ DMA EXT

Error 1987 [6] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.774 READ DMA EXT
10 00 00 00 3f 00 00 00 00 00 00 e0 00 00:01:03.102 RECALIBRATE [OBS-4]
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:02.278 READ DMA EXT

Error 1986 [5] occurred at disk power-on lifetime: 10642 hours (443 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:01.665 READ DMA EXT
25 00 00 00 08 00 00 8e 00 10 e6 e0 00 00:01:03.102 READ DMA EXT
25 00 00 00 08 00 00 9b 00 0f de e0 00 00:01:02.443 READ DMA EXT
25 00 00 00 08 00 00 1e 00 b1 2e e0 00 00:01:02.293 READ DMA EXT
25 00 00 00 08 00 00 9b 00 c3 2e e0 00 00:01:02.278 READ DMA EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00648 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11) not supported